
ともぱる
60プリウスPHEVに乗ってます
マンション住まいで充電難民ですが
近くに充電設備があるので楽しくやってます。新型プリウス乗りの方、フォローをよろしくお願いします😀
神奈川
ハンドメイド
ゲーム
映画
キャンプ
出版・報道
イラスト

ともぱる

回答数 22550>>

ともぱる
ご馳走になりました
美味しかったです
#さがみ





ともぱる

回答数 93>>

ともぱる
を追加工して加飾してみました
なかなか良い仕上げになったと思います。総額10000円ぐらい






ともぱる

回答数 115>>

ともぱる

回答数 9541>>

ともぱる

ともぱる

ともぱる

回答数 165>>

ともぱる
目が疲れた🥱


ともぱる
47%クリーム増量
ロールケーキ
横からのはみ出し量
ハンパない



ともぱる
コーティングしたので
今年遅ればせながら
初洗車
#60Priusphev





ともぱる

回答数 169>>

ともぱる

ともぱる

回答数 63>>

ともぱる

回答数 115>>

ともぱる
#XJ13
私はボディの全箇所750本のリベットを全て打ち終わりました。
なかなかかっこよくなりました
#modelfactoryhiro
#XJ13
I've finished hammering in all 750 rivets in the body.
It looks pretty cool now.

ともぱる

回答数 379>>

ともぱる

回答数 379>>

ともぱる
#XJ13
リベット周りの水性接着剤汚れを
歯ブラシで除去したので
再投稿します
I'm reposting this because I removed the water-based adhesive stains around the rivets with a toothbrush.





ともぱる
#XJ13
リベット打ちをしました
リアボディだけでかなり
時間がかかりました
なかなかリアリティが上がっていい感じです
I riveted the parts. It took a lot of time just to rivet the rear body. It looks really realistic.





ともぱる
#XJ13
私は塗装を終えたつもりでしたが、ドア見切りのエッジのダレが気になったので、サンドペーパーでエッジを再生しました。幸い下地の露出は最小限で済みました
#modelfactoryhiro
#XJ13
I thought I had finished painting, but I noticed that the edges of the door trims were sagging, so I resurfaced them with sandpaper. Luckily, the exposure of the base was minimal.










ともぱる
#XJ13
先ほどの修復を済ませて、3回ほど研ぎ出したのち、希釈2倍のウレタンクリアを仕上げに吹いて塗装は完成とします
After completing the previous repairs, sanding it down about three times, then spraying it with a 2x diluted urethane clear coat to finish off the painting.










ともぱる
#XJ13
塗装後に研ぎ出しを始めました。
1200番で磨ききれない凹凸が残っているところを#180番で完全にフラットにしたので、下地が出てしまったところが数箇所あるので修復してから研ぎ出しを再開したいと思います
#modelfactoryhiro
#XJ13
After painting, I started polishing.
I used #180 to completely flatten the uneven areas that couldn't be polished away with 1200 grit, but there are a few areas where the base coat is exposed, so I'll repair them and then resume polishing.










ともぱる

ともぱる

回答数 271>>

ともぱる

回答数 192>>

ともぱる

回答数 427>>

ともぱる

回答数 144>>

ともぱる
#XJ13
ウレタンクリア塗装しました
なんか研ぎ出さなくても
良いレベルだけど
どうしようかな、皆さんはどう思いますか?
#Model Factory Hiro
#XJ13
I painted it with urethane clear paint
It's pretty good even without polishing it
I'm not sure what to do, what do you guys think?









ともぱる
#XJ13
サーフェサー塗りました









ともぱる
#xj13
リベット穴開け完了☑️
ドリル1本破損しました








ともぱる


ともぱる
コーティングで綺麗になって
お肌スベスベ
今年も残りわずかですね









ともぱる

回答数 158>>

ともぱる
新車以上の輝き✨✨✨✨
#PolishStudio





ともぱる


ともぱる
今の奥さんに

ともぱる

ともぱる

ともぱる

回答数 11215>>

ともぱる

回答数 4570>>

ともぱる

回答数 12361>>

ともぱる

回答数 211>>

ともぱる

回答数 155>>

ともぱる
#MA1
#REMODELMK2
新しいの買った
AIREXはデザインだけでなく
作りがしっかりしてていいね👍





ともぱる

回答数 199>>